|
|
Electronic Xylophone
Čížek, Petr ; Vojáček, Zdeněk (referee) ; Marada, Tomáš (advisor)
The aim of this bachelor thesis is to design and create a working electronic xylophone which could be controlled by a programmable logic controller or by an Arduino based board. The finished xylophone could be used for promotional purposes of the faculty.
|
|
|
Printed circuit board tester
Stachera, Tomáš ; Havlíková, Marie (referee) ; Čejka, Miloslav (advisor)
The themes of this work is make a projection of printed circuit tester with focus on HW ans SW part of signal multiplexor . In the first part i will do general description of printed circuit board testing and on concrete example i will show connection of test system with connection of multiplexor. In the second part i will describe HW part of multiplexor board with real values of componets. In the third part i will describe SW for microcontroller and computer. In the end part i will review possibility of multiplexor and his parameters.
|
|
|
Back-bone deformation analysis using modern sensors
Fiala, Vojtěch ; Janoušek, Oto (referee) ; Čmiel, Vratislav (advisor)
This bachelor thesis summarizes the knowledge of the medical and technical field related to the project. In the medical section, there are mainly described areas of kinesiology and medicine related to the causes and risk factors leading to problems and diseases of the spine. In addition to the description of the disease, there are also presented the diagnostic solutions and treatment. The content of the medical part of the thesis is also a look at some commercially available products dealing also with postural problems. Part of the technical part is acquaintance with the Arduino platform and the components that are included in the practical part of the bachelor thesis. In the technical part, the area of motion sensors such as accelerometers, IMU sensors and gyroscopes are also described in more detail. Especially there is described IMU MPU-6050, which is used in this project. Further, the thesis describes the procedure in the practical part of the project, including the design of the positioning of the sensors with the positions in which the data are measured, as well as the design of the assembly and its optimization. Subsequently, the final appearance of the device, including the method of attachment on the body, and the measurement results are shown. Results are later commented and discussed. The final part of the thesis is the final summary of the results achieved and the reflections on the possibilities of further work or further adjustments and modifications of the existing equipment.
|
|
|
System of controlled generators of rectangular pulses
Holeksa, David ; Mišurec, Jiří (referee) ; Hanák, Pavel (advisor)
This bachelor thesis deals with the design system of controlled generators of rectangular pulses, which are burdened with toroidal coils. The objective is realization of the equipment to be controlled by a microcontroller, which will bring rectangular pulses to each coil according to pre-specified parameters. The resultant generator is capable of generating current pulses having an amplitude of 0.1 to 1 A and a pulse time of 1-10 ms.
|
|
|
Laboratory task of the surveillance camera system
Špondr, Marek ; Jeřábek, Jan (referee) ; Burda, Karel (advisor)
The goal of this thesis is to describe principles, technical solutions and basic components of the surveillance camera system. The second part of this thesis describes how to connect and control specific surveillance camera system. For this specific surveillance camera system is designed laboratory task for 90 minutes.
|
|
|
Electronic Xylophone
Čížek, Petr ; Vojáček, Zdeněk (referee) ; Marada, Tomáš (advisor)
The aim of this bachelor thesis is to design and create a working electronic xylophone which could be controlled by a programmable logic controller or by an Arduino based board. The finished xylophone could be used for promotional purposes of the faculty.
|
|
|
Back-bone deformation analysis using modern sensors
Fiala, Vojtěch ; Janoušek, Oto (referee) ; Čmiel, Vratislav (advisor)
This bachelor thesis summarizes the knowledge of the medical and technical field related to the project. In the medical section, there are mainly described areas of kinesiology and medicine related to the causes and risk factors leading to problems and diseases of the spine. In addition to the description of the disease, there are also presented the diagnostic solutions and treatment. The content of the medical part of the thesis is also a look at some commercially available products dealing also with postural problems. Part of the technical part is acquaintance with the Arduino platform and the components that are included in the practical part of the bachelor thesis. In the technical part, the area of motion sensors such as accelerometers, IMU sensors and gyroscopes are also described in more detail. Especially there is described IMU MPU-6050, which is used in this project. Further, the thesis describes the procedure in the practical part of the project, including the design of the positioning of the sensors with the positions in which the data are measured, as well as the design of the assembly and its optimization. Subsequently, the final appearance of the device, including the method of attachment on the body, and the measurement results are shown. Results are later commented and discussed. The final part of the thesis is the final summary of the results achieved and the reflections on the possibilities of further work or further adjustments and modifications of the existing equipment.
|
|
|
System of controlled generators of rectangular pulses
Holeksa, David ; Mišurec, Jiří (referee) ; Hanák, Pavel (advisor)
This bachelor thesis deals with the design system of controlled generators of rectangular pulses, which are burdened with toroidal coils. The objective is realization of the equipment to be controlled by a microcontroller, which will bring rectangular pulses to each coil according to pre-specified parameters. The resultant generator is capable of generating current pulses having an amplitude of 0.1 to 1 A and a pulse time of 1-10 ms.
|
|
|
Printed circuit board tester
Stachera, Tomáš ; Havlíková, Marie (referee) ; Čejka, Miloslav (advisor)
The themes of this work is make a projection of printed circuit tester with focus on HW ans SW part of signal multiplexor . In the first part i will do general description of printed circuit board testing and on concrete example i will show connection of test system with connection of multiplexor. In the second part i will describe HW part of multiplexor board with real values of componets. In the third part i will describe SW for microcontroller and computer. In the end part i will review possibility of multiplexor and his parameters.
|
|
|
Laboratory task of the surveillance camera system
Špondr, Marek ; Jeřábek, Jan (referee) ; Burda, Karel (advisor)
The goal of this thesis is to describe principles, technical solutions and basic components of the surveillance camera system. The second part of this thesis describes how to connect and control specific surveillance camera system. For this specific surveillance camera system is designed laboratory task for 90 minutes.
|
guest ::
